Features
● 10Gb/s serial optical interface compliant to 802.3ae
● Electrical interface compliant to SFF-8431 specifications for enhanced 8.5 and 10 Gigabit small formfactor pluggable module “SFP+”
● 1550nm DFB EML transmitter, APD photo-detector
● 2-wire interface for management specifications compliant with SFF 8472 digital diagnostic monitoring interface for optical transceivers
● Operating case temperature: 0 to 70 °C or-40 to 85 °C
● ll-metal housing for superior EMI performance
● Low power consumption
● Advanced firmware allow customer system encryption information to be stored in transceiver
● Cost effective SFP+ solution, enables higher port densities and greater bandwidth
● RoHS compliant
Applications
● High-speed storage area networks
● Computer cluster cross-connect
● Custom high-speed data pipes
ABSOLUTE MAXIMUM RATING
These values represent the damage threshold of the module. Stress in excess of any of the individual Absolute Maximum Ratings can cause immediate catastrophic damage to the module even if all other parameters are within Recommended Operating Conditions.
|
Parameters |
Symbol |
Min. |
Max. |
Unit |
|
Power Supply Voltage |
VCC |
0 |
3.6 |
V |
|
Storage Temperature |
Tc |
-40 |
85 |
。C |
|
Operating Case Temperature |
Tc |
0 |
70 |
。C |
|
TI |
-40 |
85 |
||
|
Relative Humidity |
RH |
5 |
95 |
% |
|
RX Input Average Power |
Pmax |
- |
0 |
dBm |
RECOMMENDED OPERATING ENVIRONMENT
Recommended Operating Environment specifies parameters for which the electrical and optical characteristics hold unless otherwise noted.
|
Parameters |
Symbol |
Min. |
Typical |
Max |
Unit |
|
Power Supply Voltage |
VCC |
3.135 |
3.3 |
3.465 |
V |
|
Power Supply Current |
Icc |
600 |
mA |
||
|
Operating Case Temperature |
TC |
0 |
25 |
70 |
。C |
|
TI |
-40 |
25 |
85 |
OPTICAL CHARACTERISTICS
The following optical characteristics are defined over the Recommended Operating Environment unless otherwise specified.
|
Parameters |
Unit |
Values |
|
Transmitter |
||
|
Center wavelength (range) |
nm |
1530 -1565 |
|
Side Mode Suppression Ratio (min) |
dB |
30 |
|
Launched power |
||
|
– maximum (Average) |
dBm |
5 |
|
– minimum (Average) |
dBm |
0 |
|
Transmitter and dispersion penalty (max) |
dB |
3 |
|
Average launch power of OFF transmitter (max) |
dBm |
-30 |
|
Extinction ratio (min) |
dB |
6 |
|
RIN12 OMA (max) |
dB/Hz |
-128 |
|
Optical Return Loss Tolerance (min) |
dB |
12 |
|
Receiver |
||
|
Center wavelength (range) |
nm |
1100-1610 |
|
Receive overload (max) in average power(note 1) |
dBm |
-8 |
|
Receive sensitivity (min) in average power(note 1) |
dBm |
-24 |
|
Receiver Reflectance (max) |
dB |
-12 |
|
Los Assert(min) |
dBm |
-35 |
|
Los Dessert(max) |
dBm |
-25 |
|
Los Hysteresis(min) |
dB |
0.5 |
|
Stressed eye jitter (min)(note 2) |
UIp-p |
0.3 |
|
Receive electrical 3dB upper cutoff frequency (max) |
GHz |
12.3 |
|
Receiver power (damage, Max) |
dBm |
1.5 |
Notes:
1. Average optical power shall be measured using the methods specified in TIA/EIA-455-95.
2. Receiver sensitivity is informative. Stressed receiver sensitivity shall be measured with conformance test signal for BER =1x 10-12 .
3. Vertical eye closure penalty and stressed eye jitter are the test conditions for measuring stressed receiver sensitivity. They are not the required characteristic of the receiver.
4. Power budget is defined as the different between the Rx sensitivity and the Tx output power of the interface.
5. Path penalty is intended as the power penalty of the interface between back-to-back and the maximum applied dispersion
ELECTRICAL CHARACTERISTICS
The following electrical characteristics are defined over the Recommended Operating Environment unless otherwise specified.
|
Parameter |
Symbol |
Min. |
Typical |
Max |
Unit |
Notes |
|
Data Rate |
- |
10.3125 |
- |
Gbps |
||
|
Power Consumption |
- |
800 |
1000 |
mW |
||
|
Transmitter |
||||||
|
Single Ended Output Voltage Tolerance |
-0.3 |
- |
4 |
V |
||
|
Ccommon mode voltage tolerance |
15 |
- |
- |
mV |
||
|
Tx Input Diff Voltage |
VI |
180 |
800 |
mV |
||
|
Tx Fault |
VoL |
-0.3 |
0.4 |
V |
At 0.7mA |
|
|
Data Dependent Input Jitter |
DDJ |
0.1 |
UI |
|||
|
Data Input Total Jitter |
TJ |
0.28 |
UI |
|||
|
Receiver |
||||||
|
Single Ended Output Voltage Tolerance |
-0.3 |
- |
4 |
V |
||
|
Rx Output Diff Voltage |
Vo |
300 |
850 |
mV |
||
|
Rx Output Rise and Fall Time |
Tr/Tf |
30 |
ps |
20% to 80% |
||
|
Total Jitter |
TJ |
0.7 |
UI |
|||
|
Deterministic Jitter |
DJ |
0.42 |
UI |
|||
MECHANICAL
Comply to SFF-8432 rev. 5.0, the improved Pluggable form factor specification.
Key Mechanical Dimensions
订单信息
|
产品型号 |
封装 |
波长(-xx) |
速率(xx) |
传输距离 (-xx) |
x |
等级(x) |
|
BYCS-151X-H0Dxx |
SFP+ |
13=1310nm |
1X=10.3GBP/s |
80=80km |
空 不带DDM |
空 商业级 |