Features
● 10Gb/s serial optical interface compliant to 802.3ae 10GBASE-ER
● Electrical interface compliant to SFF-8431 specifications for enhanced 8.5 and 10 Gigabit small form factor pluggable module “SFP+”
● CWDM DFB transmitter,PIN photo-detector
● 2-wire interface for management specifications compliant with SFF 8472 digital diagnostic monitoring interface for optical transceivers
● Operating case temperature: 0 to 70 °C or-40 to 85 °C
● ll-metal housing for superior EMI performance
● Low power consumption
● Advanced firmware allow customer system encryption information to be stored in transceiver
● Cost effective SFP+ solution, enables higher port densities and greater bandwidth
● RoHS compliant
Applications
● High-speed storage area networks
● Computer cluster cross-connect
● Custom high-speed data pipes
ABSOLUTE MAXIMUM RATING
These values represent the damage threshold of the module. Stress in excess of any of the individual Absolute Maximum Ratings can cause immediate catastrophic damage to the module even if all other parameters are within Recommended Operating Conditions.
|
Parameters |
Symbol |
Min. |
Max. |
Unit |
|
Power Supply Voltage |
VCC |
0 |
3.6 |
V |
|
Storage Temperature |
Tc |
-40 |
85 |
。C |
|
Operating Case Temperature |
Tc |
0 |
70 |
。C |
|
TI |
-40 |
85 |
||
|
Relative Humidity |
RH |
5 |
95 |
% |
|
RX Input Average Power |
Pmax |
- |
7 |
dBm |
Note：
1、Exceeding any of these values may immediately damage the device.
RECOMMENDED OPERATING ENVIRONMENT
Recommended Operating Environment specifies parameters for which the electrical and optical characteristics hold unless otherwise noted.
|
Parameters |
Symbol |
Min. |
Typical |
Max |
Unit |
|
Power Supply Voltage |
VCC |
3.135 |
3.3 |
3.465 |
V |
|
Power Supply Current |
Icc |
450 |
mA |
||
|
Operating Case Temperature |
TC |
0 |
25 |
70 |
。C |
|
TI |
-40 |
25 |
85 |
OPTICAL CHARACTERISTICS
The following optical characteristics are defined over the Recommended Operating Environment unless otherwise specified.
|
Parameters |
Unit |
Values |
|
Operating Reach |
m |
40K |
|
Transmitter |
||
|
Center wavelength (range) |
nm |
λ+ -6.5 |
|
Side Mode Suppression Ratio (min) |
dB |
30 |
|
Launched power |
||
|
– maximum (Average) |
dBm |
+4 |
|
– minimum (Average) |
dBm |
-1 |
|
Average launch power of OFF transmitter (max) |
dBm |
-30 |
|
Transmitter and Dispersion Penalty(max) |
dBm |
3 |
|
Extinction ratio (min) |
dB |
6 |
|
RIN12 OMA (max) |
dB/Hz |
-128 |
|
Optical Return Loss Tolerance (min) |
dB |
12 |
|
Receiver |
||
|
Center wavelength (range) |
nm |
1260-1620 |
|
Receive overload (max) in average power(note 1) |
dBm |
0.5 |
|
Receive sensitivity (min) in average power(note 1) |
dBm |
-16 |
|
Receiver Reflectance (max) |
dB |
-12 |
|
Los Assert(min) |
dBm |
-30 |
|
Los Dessert(max) |
dBm |
-16 |
|
Los Hysteresis(min) |
dB |
0.5 |
|
Receive electrical 3dB upper cutoff frequency (max) |
GHz |
12.3 |
|
Receiver power (damage, Max) |
dBm |
+7 |
Note：
1、Average optical power shall be measured using the methods specified in TIA/EIA-455-95.
2、Power budget is defined as the different between the Rx sensitivity and the Tx output power of the interface.
3、Path penalty is intended as the power penalty of the interface between back-to-back and the maximum applied dispersion.
ELECTRICAL CHARACTERISTICS
The following electrical characteristics are defined over the Recommended Operating Environment unless otherwise specified.
|
Parameter |
Symbol |
Min. |
Typical |
Max |
Unit |
Notes |
|
Data Rate |
- |
10.3125 |
- |
Gbps |
||
|
Power Consumption |
- |
800 |
1000 |
mW |
||
|
Transmitter |
||||||
|
Single Ended Output Voltage Tolerance |
-0.3 |
- |
4 |
V |
||
|
C common mode voltage tolerance |
15 |
- |
- |
mV |
||
|
Tx Input Diff Voltage |
VI |
180 |
800 |
mV |
||
|
Tx Fault |
VoL |
-0.3 |
0.4 |
V |
At 0.7mA |
|
|
Data Dependent Input Jitter |
DDJ |
0.1 |
UI |
|||
|
Data Input Total Jitter |
TJ |
0.28 |
UI |
|||
|
Receiver |
||||||
|
Single Ended Output Voltage Tolerance |
-0.3 |
- |
4 |
V |
||
|
Rx Output Diff Voltage |
Vo |
300 |
850 |
mV |
||
|
Rx Output Rise and Fall Time |
Tr/Tf |
30 |
ps |
20% to 80% |
||
|
Total Jitter |
TJ |
0.7 |
UI |
|||
|
Deterministic Jitter |
DJ |
0.42 |
UI |
|||
MECHANICAL
Comply to SFF-8432 rev. 5.0, the improved Pluggable form factor specification.
Order Information
|
产品型号 |
封装-C |
波长(-xx) |
速率(xx) |
传输距离 (-xx) |
x |
等级(x) |
|
BYCS-Cxx1X-40D xx |
SFP+ CWDM EML |
1470~1610nm |
1X=10.3GBP/s |
02≤2km |
空 不带DDM |
空 商业级 |
Wavelength Guide Table
|
Wavelength |
xx |
Wavelength |
xx |
Wavelength |
xx |
|
1471 nm |
47 |
1591nm |
59 |
||
|
1491 nm |
49 |
1611nm |
61 |
||
|
1511 nm |
51 |
||||
|
1531 nm |
53 |
||||
|
1551 nm |
55 |
||||
|
1571 nm |
57 |